Search results for " Mechanical Engineering."

A Model for High-Cycle Fatigue in Polycrystals

2018

A grain-scale formulation for high-cycle fatigue inter-granular degradation in polycrystalline aggregates is presented. The aggregate is represented through Voronoi tessellations and the mechanics of individual bulk grains is modelled using a boundary integral formulation. The inter-granular interfaces degrade under the action of cyclic tractions and they are represented using cohesive laws embodying a local irreversible damage parameter that evolves according to high-cycle continuum damage laws. The consistence between cyclic and static damage, which plays an important role in the redistribution of inter-granular tractions upon cyclic degradation, is assessed at each fatigue solution jump,…

Hybrid Equilibrium Finite Element Formulation for Cohesive Crack Propagation

2019

Equilibrium elements have been developed in hybrid formulation with independent equilibrated stress fields on each element. Traction equilibrium condition, at sides between adjacent elements and at sides of free boundary, is enforced by use of independent displacement laws at each side, assumed as Lagrangian parameters. The displacement degrees of freedom belongs to the element side, where an extrinsic interface can be embedded. The embedded interface is defined by the same stress fields of the hybrid equilibrium element and it does not require any additional degrees of freedom. The extrinsic interface is developed in the consistent thermodynamic framework of damage mechanics with internal …

Virtual Element Method: Micro-Mechanics Applications

2019

In this contribution we present an application of the lowest order Virtual Element Method (VEM) to the problem of material computational homogenization. Material homogenization allows retrieving material properties through suitable volume averaging procedures, starting from a detailed representation of the micro-constituents of the considered material. The representation of such microstructure constitutes a remarkable effort in terms of data/mesh preparation, especially when there is not evident microstructural regularity. For such a reason, computational micromechanics may represent a challenging benchmark for showing the potential of VEM. In this contribution, polycrystalline materials ar…

A Model for Low-Cycle Fatigue in Micro-Structured Materials

2019

A microscale formulation for low-cycle fatigue degradation in heterogeneous materials is presented. The interface traction-separation law is modelled by a cohesive zone model for low-cycle fatigue analysis, which is developed in a consistent thermodynamic framework of elastic-plastic-damage mechanics with internal variables. A specific fatigue activation condition allows to model the material degradation related to the elastic-plastic cyclic loading conditions, with tractions levels lower than the static failure condition. A moving endurance surface, in the classic framework of kinematic hardening, enables a pure elastic behaviour without any fatigue degradation for low levels of cyclic tra…

A Thermodynamically Consistent CZM for Low-Cycle Fatigue Analysis

2018

A cohesive zone model for low-cycle fatigue analysis is developed in a consistent thermodynamic framework of elastic-plastic-damage mechanics with internal variable. A specific fatigue activation condition allows to model the material degradation related to the elastic-plastic cyclic loading conditions, with tractions levels lower than the damage activation condition. A moving endurance surface, in the classic framework of kinematic hardening, enables a pure elastic behavior without any fatigue degradation for low levels loading conditions.

Evaluation of nano/submicro pores in suspension plasma sprayed YSZ coatings

2019

Abstract Nano-submicro pores could considerably influence the coating performances and thus should be properly designed for the intended applications. However, it is challenging to characterize accurately such small pores in coatings. In this study, YSZ coatings were firstly manufactured by suspension plasma spray (SPS) and the nano-submicro pores in as-prepared coatings were investigated using Ultra-small-angle X-ray scattering (USAXS). Afterwards, a multivariate analysis on the effect of five different process parameters was carried out. The two main results showed that: 1) the nano-submicro pores content in coatings has a negative correlation with suspension mass load and powder size, an…

Spark Plasma Sintering of Metallic Glasses

2019

Spark plasma sintering (SPS) of metallic glasses (MG) can be quite different from sintering crystalline metallic alloys. Indeed, MG behave differently with increasing temperature, as they encounter a glass transition and devitrification. Their shaping can thus be compared to what can be performed on thermoplastic polymers. SPS is a promising way to prepare bulk parts from amorphous powders, since it allows very fast heating and cooling rates. It gives an advantage to avoid or limit devitrification of the amorphous phase upon the thermal cycle. However, diffusion mechanisms, which generally control densification, are activated at temperatures that are not compatible with MG structural integr…

Estimation des incertitudes de mesure sur bras polyarticulé portable par méthode de Monte Carlo

2013

International audience; Les bras polyarticulés portables ont progressivement évolué et sont de plus en plus utilisés dans l’industrie. Cependant, à l’heure actuelle, la traçabilité de ces dispositifs est difficile à effectuer et les incertitudes de mesures relatives à l’utilisation de ces appareils ne sont pas quantifiées. Le travail mené consiste à déterminer les incertitudes de mesures associées à la quantification, par un bras polyarticulé portable, des caractéristiques géométriques et dimensionnelles d’une pièce mécanique. Les travaux visant à élaborer un modèle d’incertitude de mesure, sont basés sur la méthode de Monte Carlo du supplément 1 du Guide pour l'expression de l'incertitude …

Rigid Closed‐Cell PUR Foams Containing Polyols Derived from Renewable Resources: The Effect of Polymer Composition, Foam Density, and Organoclay Fill…

2017

Predicting plot soil loss by empirical and process-oriented approaches. A review

2018

Soil erosion directly affects the quality of the soil, its agricultural productivity and its biological diversity. Many mathematical models have been developed to estimate plot soil erosion at different temporal scales. At present, empirical soil loss equations and process-oriented models are considered as constituting a complementary suite of models to be chosen to meet the specific user need. In this paper, the Universal Soil Loss Equation and its revised versions are first reviewed. Selected methodologies developed to estimate the factors of the model with the aim to improve the soil loss estimate are described. Then the Water Erosion Prediction Project which represents a process-oriente…